APJ EngineersAPJ WhatsApp

PCC Panel Manufacturer (Power Control Centre)

A power control centre (PCC) is the main LT switchboard of a plant or building. It takes power from the transformer or DG set and feeds every downstream board. APJ Engineers builds PCC panels up to 6300 A at its own works in Vasai, near Mumbai.

Main panel at its factory acceptance test, APJ works
Main panel at its factory acceptance test, APJ works

What a PCC panel does

The PCC is the first board after the transformer. It receives the full load current of the installation, so it carries the largest busbars and breakers on site and must withstand the highest fault current.

A typical PCC has one or more incomers (transformer and DG), a bus coupler where there are two sources, and outgoing feeders to MCCs, APFC panels, distribution boards and large loads.

What goes into it

  • Incomers and bus couplers: air circuit breakers (ACB), with interlocking between sources
  • Outgoing feeders: ACBs or moulded-case circuit breakers (MCCB)
  • Main horizontal and vertical busbars in electrolytic copper or aluminium, tin plated
  • Metering and protection: multifunction meters, current transformers, protection relays
  • Enclosure in CRCA sheet, powder coated, IP42 / IP54 / IP65 as specified

What APJ builds

PCC panels at 415 V, 3 phase, up to 6300 A, to IEC 61439-2 and IS 8623, built to the client's single-line diagram. The design is covered by ASTA type tests up to 6300 A / 85 kA, a CPRI test at 4000 A / 65 kA, an ERDA temperature-rise test at 4000 A and an ASTA internal-arc test at 85 kA.

Enclosures are laser cut, bent, pre-treated and powder coated in-house. Read how design and routine verification cover each board, and how to choose the form of internal separation.

What to send for a quotation

  • Single-line diagram (SLD) or BOQ
  • Incomer rating and the fault level at the board
  • Preferred switchgear make, busbar material (copper or aluminium) and IP rating
  • Cable entry (top or bottom) and any size limit at site
  • Delivery location and the date you need it

The full list is in our quotation checklist.

Tested before it leaves

Every panel gets an IEC 61439-1 factory acceptance test with recorded readings, photos and a video, witnessed by the client where they wish. Its FAT QR then opens the full record, including later site and service reports.

How our traceability works

Type-test certificates

  • ASTA 6300 A / 85 kA (forced-cooled)
  • ASTA 4000 A / 65 kA
  • CPRI 4000 A / 65 kA
  • ERDA temperature-rise test, 4000 A
  • ERDA IP65 and IP55
  • ASTA internal arc, 85 kA for 0.5 s

Request a quotation

Tell us what you need. Your request goes straight to our sales team.

Frequently asked questions

What is the difference between a PCC and an MCC?

A PCC distributes power: it has a few large feeders to other boards. An MCC controls motors: it has many smaller feeders, each with a starter. In most plants the PCC feeds one or more MCCs.

Up to what current does APJ make PCC panels?

Up to 6300 A at 415 V. The design is ASTA type-tested up to 6300 A / 85 kA.

Which form of separation should a PCC have?

It is agreed between buyer and maker. Main PCCs are commonly specified as Form 3b or Form 4b so that one feeder can be worked on while the others stay live. State it in the enquiry.

Where are APJ panels made?

At APJ Engineers' own works at Pelhar, Vasai (Palghar district), near Mumbai: Plot No. 333, Pelhar Village, Opp. Apple Industries, Nalasopara Highway Road, Vasai (East), Palghar, Maharashtra 401208, India.

Is every panel tested before dispatch?

Yes. Every panel gets a factory acceptance test (FAT): IEC 61439-1 routine verification with recorded readings, photos and a test video, using instruments with current calibration certificates. A panel is released for dispatch only after its FAT is passed.

Can I check the test record of my panel?

Yes. Each panel carries a FAT QR code. Scan it, or type the code under it on apje.in, to open that panel's FAT report, drawings and site reports.

Do you supply outside Mumbai?

Yes. APJ supplies across India, with on-site supply, installation, testing and commissioning (SITC) teams.

How do I get a quotation?

Send your single-line diagram or BOQ on WhatsApp (+91-9967717710), call +91-9819917710, or email apj@apje.in.